Chevy Tri Five Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-17 of 17 Results
  1. Chit Chat Area, Anything on your mind goes here.
    Just swung by. Shelves of deals.... Ifound & bought an adj race seat mount, need for gasser project. Cu TF radiator reg $860 for $300 ish. 10% off 50% marked. BEST: TCI FLEX PLATES DATE EXPIRED $10/EA....for street, most race it's still SFI. HOLLEY 850 DP dichromate vintage color apart...
  2. Headers and Exhaust System
    Hey Everyone, New to the forum and did a search but haven't seen anything posted on this in more than a few years. (Or maybe I'm not navigating the site correctly) Anyways, I got a 5.7 LS1 with a 4l60e out of a 2000 Camaro That I'm planning on dropping in my 56 as soon as I can find the right...
  3. Headers and Exhaust System
    Hello, so my full length headers have been hanging low for a while, and finally kicked the bucket. My neighbor gave me a set of block hugger Sanderson headers. (If you’ve seen the set for tri five on the Sanderson website, it’s basically two of the block huggers.) The website says they don’t...
  4. Headers and Exhaust System
    Hi All, I apologize if this has been asked and answered but I'm stuck. I'm building a '55 Bel Air Sedan hot rod from the rails and I went the rack & pinion route. We mounted the dummy small block (front mount) and trans and when we put the headers on, we had clearance issues on the left side...
  5. Headers and Exhaust System
    I will start with I have searched through the forum, but was not able to find the specific information needed. I have a 1956 Chevy 210 4dr with a 396 big block with oval port heads. The current headers on the the vehicle are only 4.5 inches off the ground on the passenger side and about 6...
  6. Wanted Section
    Good morning all Tri5 fans out there, we need your help, We are looking for our next project and need some assistance (lol, guinea pig really, lol). We are looking to make our competition a bit more uncomfortable and really need a Tir 5 Belair with an LS motor swap to develop a bad ass set of...
  7. Headers and Exhaust System
    Have a machine shop here building us a 383 with Vortec heads to go in front of a 200R4. At some point after the SBC goes in I'm going to yank the manual steering box and steering column and put in PS (likely R&P). (Yes, I know it'd be easier to do w/the engine out, but the budget won't support...
  8. Headers and Exhaust System
    I tried a search, and found a lot of threads, but not really the info I was looking for. I'm putting an A833 4 speed/sbc combo in my 57, and will eventually run a 500 ps box. I'll be running an old set of 186 heads that I used to run on a LT-1in my 59 Vette. The previous owner ported the...
  9. Headers and Exhaust System
    G'day Guys, I am in Australia and I was wondering if I could get some advice from you, I have a 57 2 door HT/Pillarless Belair with a 350 CMJ block, standard straight plug heads and a turbo 700 trans, I know that this question has probably been asked dozens of times however if I could get some...
  10. Member Classifieds
    Here is a good set of Hooker Headers I took off my '55 Chevy. The only reason I took them off is because I changed the complete exhaust. There are no leaks, and no holes in them. They are "under the car" headers for a Big-Block. They fit a 396, 402, 427 or 454 They have 1 7/8 in. tubes...
  11. New Member Introductions
    Hi gang, first post. Thanks!
  12. Project Update Section, Post Project Updates Here
    Hi everyone. I’m not sure where to begin so I guess I’ll start by properly introducing myself. My name is James Bates, born and raised in Ramona CA. It’s a small town in San Diego County in which I have seen a few Tri Fives in. I’m just curious to know if member on this form is from Ramona...
  13. Super Stock/Pro Street & Modified Disc. 55-56-57
    Hey y'all, I've searched the forums on headers and just have a quick question. Will blockhuggers work on a 350/th400? Found a great deal but dont want a ton of aggravation. Thanks!
  14. Trifive Gassers
    Anyone running the Patriot Fenderwell's P/n# H8035. for 219.99 from summit it looks like a killer deal. They are going on a 55 belir. 427BBC, side engine mounts. manual steering
  15. Super Stock/Pro Street & Modified Disc. 55-56-57
    I am working on my 55' Bel Air with a 400sb and badly need to replace the shot to **** headers. I've been looking around on line and found some shorty hugger headers on ebay made by KMJ Performance for about $75.00, they're painted steel and not heat coated at all but the welds and machining...
  16. Big Block Install Questions and Answers
    Hi everybody im looking for a manual rack and pinion setup for my 55 210 2 door wagon 490 cid big block. I already have the ididit column and the stock manual box. I'm trying to get the clearance of the headers on the steering. i have had heddman hustler in frame headers and I had to beat the...
  17. Bella57

    Underside of the Pink Bel Air!
1-17 of 17 Results
Top